Skip to content

HRC Cost Model 2026 | Hot-Rolled Coil Conversion Costs

Slab to HRC Conversion Costs


Hot-Rolled Coil Conversion Cost Model, 2026
Cost ComponentFactorUnitCost (US$/unit)Fixed (US$/t)Variable (US$/t)Total (US$/t)
Slab cost1.035t5800.00600.30600.30
Delivery costs1.035t2.50.002.592.59
Manpower1MHPT17.54.3813.1317.50
Natural gas1.5GJ50.007.507.50
Electricity60kWh0.070.004.204.20
Work rolls1unit10.001.001.00
Other consumables1unit20.002.002.00
Scrap credit2.8%t3140.00−8.79−8.79
Packaging costs1unit20.002.002.00
Depreciation1t8.58.500.008.50
SG&A costs1unit55.000.005.00
Total cost–––17.88623.92641.80

Swipe the table sideways for more columns; the first column stays in place.

Costs per tonne of hot-rolled coil. Figures as calculated in the model, so rows may not add exactly to the totals because of rounding. Source: Metals Consulting International. A dash (–) means not applicable. Data as of September 2026.



Hot Strip Mill Cost Modelling Notes and Assumptions

The Steel Costing Model

The economic model shown above has been prepared to show how hot-rolled coil costs can be estimated through a simple cost benchmarking approach. The predicted total cost is not meant to represent an actual cost for any particular hot strip mill. It is a notional figure only – albeit one that is built on fairly representative current input cost data.

Input Costs

Key input costs are based on anticipated mid-2026 world average costs. Ferrous scrap is priced at about US$314 per tonne and steel slab at about US$580/t. Other factor costs e.g. natural gas or electricity are at market prices, with factor usage (manpower, yield etc) estimated by our technical experts and economists. SG&A denotes sales, general and administration cost. MHPT denotes man hours per tonne (a measure of labour force productivity).

The Steel Product

The steel product that is costed above is a tonne of hot-rolled steel coil of approx 2 mm or 3 mm gauge. The HRC conversion cost is for a notional medium size steelmaker who purchases slab on the open market and rolls this into coil on a traditional tandem hot rolling mill of perhaps 1 or 2 Mt per year capacity. Average labour productivity is assumed at a gross blue collar wage cost of US$42k/year. To prepare cost benchmarks for specific locations please contact us (see below). Steel costs for the BOF steelmaking process route (oxygen steelmaking) may be found on our BOF steelmaking costs page.

The Business Environment

Site visitors are advised that all cost estimates shown should be adjusted to reflect the facility set-up in which the steel plant operates. Thus, energy costs would be increased [higher natural gas costs] if slab was allowed to cool prior to rolling. Electricity cost could possibly also be reduced with ownership of an in-house power plant. Depreciation costs above are based on an HSM capex cost of US$170 per tonne depreciated over about 20 years; this cost could be significantly lower in the case of a narrow strip mill, and much higher in the case of a Steckel mill. Labour productivity may also be better than shown (e.g. in recently-built plants).

Accounting Methods

Actual costing estimates may also differ because of local accounting practices. For example, the figures above assume straight line depreciation over a 20-year asset lifetime. The estimates also assume that 25% of labour costs are fixed. The model above endeavours to present the economic data on the basis of standard management accounting practices. Users of the model should be clear that the model is likely to require adaptation for different accounting circumstances.

Cost Model Updates

To estimate the impact of a change in any main input (e.g. geographic location, slab cost, natural gas cost, labour cost etc) on the total, fixed or variable production costs of any steel product (semi-finished; or flat, long or pipe) made through either main production process route, please contact our steel cost economists.

Need costs for your own plant or location? Request a custom cost model →

How to Cite This Page

Metals Consulting International (2026) 'HRC Cost Model: Hot Rolled Coil Production Economics', SteelOnTheNet. Available at: https://www.steelonthenet.com/resources/cost-models/hrc.html (Accessed: 16 November 2026).